GarminCure3 tool - the new way to create cure firmwares for

O elektronice i wewnętrznym oprogramowaniu naszych Garminów. Chipsety, anteny zewnętrzne, baterie, karty pamięci, naprawy. Także o nieoficjalnych firmware, przeróbkach sprzętowych i innych rodzajach tuningu.

Moderator: PouchX

GarminCure3 tool - the new way to create cure firmwares for

Postprzez Jep_Pavel » Cz, 05 sty 2012 23:49

Here is a special firmware patcher from Kunix and Alexander (known as the author of the firmware Deluxe). Patched firmwares enter the mass storage mode immediately, without going through the normal booting process ( e.g. they don’t display “Loading maps…” and so on). That’s why they don’t crash or hang up, therefore, they can be used for curing. It works even if your device was formatted into NTFS.

The typical curing algorithm (in general) looks like this:

1. Flash your device with the patched firmware (see below for more details).
2. Don’t disconnect your device from the PC. It should enter the mass storage mode and the PC should detect it as a new flash drive.

  • If the filesystem on the flash drive is OK then you should try removing/renaming some files that could cause problems. Start from those files that were created/copied last. Don’t forget about making backups.
  • If removing files doesn’t help, or you’ve accidentally formatted the flash drive into NTFS, or its filesystem is corrupted then you should reformat the flash drive into FAT or FAT32. Remember that when your device is cured you can restore most of the missing files by running WebUpdater.
  • Unfortunately, some devices don't boot if the flash drive is totally empty (for example, nuvi 24x0). Then try copying it's contents from a healthy device of the same or close model. If even copying from the same model doesn't help then the problem is somewhere else, you need some other cure.

3. “Safely” disconnect your device from the PC. It should turn off in a few seconds. If it doesn’t then press the power button for at least 30 seconds. Be aware that some devices don’t turn off this way. You should know how to turn your device off if it hangs up.
4. Flash your device with the original firmware (see below for more details), and see if it boots normally. If it still doesn’t boot then go to step 1.


How to flash your device with the patched or original firmware:

1. Download GarminCure3.exe and updater.exe from here: http://dl.dropbox.com/u/55759275/GarminCure3.zip
GarminCure3.exe user interface looks like this:
Obrazek
2. Download the original firmware from the Garmin website
3. Run GarminCure3.exe and open the downloaded firmware with it. You can do it by dragging the firmware file into “Input file” box or by typing the path to the file or by pressing the “…” button.
4. Press “Make firmware” button. Before doing that make sure the right option is selected from “CURE” and “ORIGINAL”.
5. If everything is ok, “Processing OK : )” message will be printed and all controls inside “Output file(s)” box will be enabled. If it doesn’t happen, please, let me know.
6. Then you can drag patched firmware files from the rectangle displaying their names. Or just run Updater.exe by pressing the corresponding button. The firmwares will be saved automatically.
7. Then put your device into pre-boot mode and flash the firmware with updater.exe. Search through this forum for what is pre-boot mode and how to flash devices with updater.exe.

Devices that can be cured.
The tool was tested on nuvi 200 (HWID=660), 6x0, 13xx/14xx, 22x0, 24x0, 37xx. So it should work for all nuvis.
Almost all Garmin firmwares are patchable (except some marine GPSmaps and linux-based devices), but this doesn't guarantee successful curing, of course.
Known bugs and issues:

There is an issue under Windows Seven and Windows Vista if UAC is enabled. If you want GarminCure3.exe to run Updater.exe then GarminCure3.exe should be run as Administrator. But then drag&drop won’t work.
Patched firmwares are stored inside GarminCure3-TEMP folder located near GarminCure3.exe. Don’t forget to delete GarminCure3-TEMP from time to time. Before deleting make sure updater.exe isn’t running.

P.S.
I hope this firmware is to facilitate work PouchX :D
Ostatnio edytowano N, 08 sty 2012 20:57 przez Jep_Pavel, łącznie edytowano 4 razy
Jep_Pavel
Początkujący
 
Posty: 40
Dołączył(a): Wt, 31 mar 2009 19:19
Lokalizacja: RUSSIA

Re: GarminCure3 tool - the new way to create cure firmwares for

Postprzez popej » Pt, 06 sty 2012 11:49

Nie sprawdzałem jak działa, ale wygląda na bardzo przydatne narzędzie. Dla porządku należałoby dodać, że autorem tego rozwiązania jest kunix.
popej
Montana 700, 3540T, PL Topo, OSM, CNE; PocoX3Pro, OsmAnd+
Avatar użytkownika
popej
Garniak
 
Posty: 6877
Dołączył(a): Wt, 10 kwi 2007 23:22
Lokalizacja: Gdańsk

Re: GarminCure3 tool - the new way to create cure firmwares for

Postprzez Jep_Pavel » Pt, 06 sty 2012 19:34

The program belongs to the author, Alexander and Kunix. :D
Jep_Pavel
Początkujący
 
Posty: 40
Dołączył(a): Wt, 31 mar 2009 19:19
Lokalizacja: RUSSIA

Re: Software Missing i Loading Maps...

Postprzez zinke » Cz, 26 sty 2012 9:16

GarminCure3 !!!
цитируем автора; kunix
информация с сайта: http://www.gpspassion.com/forumsen/topi ... _ID=143809 Пропатченная утилитой прошивка может работает даже если у вашего устройства Flash был отформатирован в NTFS!!!!!!!!!. Инструмент был протестирован на NUVI 200 (HWID = 660), 6x0, 13xx/14xx, 22x0, 24x0, 37xx.
Так оно и должно работать для всех nuvis!!!!!!!!!!!!!.
zinke
Nowy
 
Posty: 1
Dołączył(a): Wt, 25 paź 2011 10:25

Re: GarminCure3 tool - the new way to create cure firmwares for

Postprzez PouchX » Pt, 01 mar 2013 7:26

Wersja PL w załączniku.

GarminCure3PL.jpg
Załączniki
GarminCure3PL.rar
(169.22 KiB) Pobrane 5952 razy
Avatar użytkownika
PouchX
Radny
 
Posty: 4537
Dołączył(a): Pt, 16 mar 2007 8:22
Lokalizacja: Poznań

Re: GarminCure3 tool - the new way to create cure firmwares for

Postprzez Krawol » Pt, 12 sty 2018 20:49

ktoś wie gdzie można znaleźć "updater.exe" ten link podany jest nieaktywny.
Krawol
Nowy
 
Posty: 3
Dołączył(a): Pt, 12 sty 2018 13:15

Re: GarminCure3 tool - the new way to create cure firmwares for

Postprzez PouchX » Cz, 25 sty 2018 4:31

Avatar użytkownika
PouchX
Radny
 
Posty: 4537
Dołączył(a): Pt, 16 mar 2007 8:22
Lokalizacja: Poznań

Re: GarminCure3 tool - the new way to create cure firmwares for

Postprzez ekeshkekesh » Wt, 19 lis 2019 19:43

PouchX napisał(a):http://pouchx.5v.pl/Garniak/


Są jakieś aktualizacje do linków. Te niestety nie działają. GarminCure3 da się znaleźć w sieci, ale z updater.exe jest większy problem.
ekeshkekesh
Nowy
 
Posty: 4
Dołączył(a): Pn, 18 lis 2019 8:20

Re: GarminCure3 tool - the new way to create cure firmwares for

Postprzez sdsyc » Wt, 19 lis 2019 20:18

Auto: Android Auto + OsmAnd+ + UMP, mapy.cz + OSM, Google Maps
Nagarstek: Fenix 5 Plus Sapphire + TopoActive Europe + OSM Freizeikarte + UMP
W telefonach: Locus / Brouter, OsmAnd+ + OSM + UMP, mapy.cz
sdsyc
Radny
 
Posty: 3361
Dołączył(a): Śr, 27 lut 2008 9:03

Re: GarminCure3 tool - the new way to create cure firmwares for

Postprzez dejvic » Cz, 23 wrz 2021 19:02

this tools not ready with Garmin Fenix. Have you got someone another tools?
Or do you have fw for garmin Fenix 5 and 5s at the RGN format for updater? thank you David
dejvic
Nowy
 
Posty: 1
Dołączył(a): Cz, 23 wrz 2021 18:53


Powrót do Hardware i firmware

Kto przegląda forum

Użytkownicy przeglądający ten dział: Brak zalogowanych użytkowników i 13 gości